Buy Penberthy Emerson LH Series Jet Pumps HERE!
The "L" series jets use a liquid motive (usually water) to create the suction through the jet.
Note: Eductors or Jet Pumps need to be sized properly to work properly. Just the NPT size is not enough for sizing the application. If the PSI pressure is too low to overcome head pressure the jet will choke, if the GPM flow rate is not sufficient enough to over come the head pressure or suction requirement the jet will choke.
Features of Emerson Penberthy Jet Pumps (Eductors)
• Simple design with no moving parts to wear out. • No lubrication required.
• Virtually maintenance-free.
• Easy to install without special structures or foundations.
• Self-priming.
• Cast, fabricated or non-metallic constructions.
• Variety of materials to suit specific characteristics of the process liquids.
• Critical flow paths machined smoothly with
no abrupt turns or steps, producing the most efficient flow during the motive function.
Suitable for a broad range of applications including: handling condensate, pumping wells, circulating solutions, emptying cesspools, pumping brine solutions, extracting solvents, draining cellars, pumping out barges, acidifying, causticizing oils, producing emulsions,elevation water.
• Simple design with no moving parts to wear out. • No lubrication required.
• Virtually maintenance-free.
• Easy to install without special structures or foundations.
• Self-priming.
• Cast, fabricated or non-metallic constructions.
• Variety of materials to suit specific characteristics of the process liquids.
• Critical flow paths machined smoothly with
no abrupt turns or steps, producing the most efficient flow during the motive function.
General Application FOR PENBERTHY JET PUMP EDUCTORS
Technical Data
Materials: Bronze, iron, carbon steel, 316 SS, PVC, CPVC, PP, PVDF, MONEL, HASTELLOY C
Sizes: 1⁄2” to 12”
Pressure range: 15 to 200 psig (1 to 13.8 barg)
Temperature(max): 200°F(93°C)
Materials: Bronze, iron, carbon steel, 316 SS, PVC, CPVC, PP, PVDF, MONEL, HASTELLOY C
Sizes: 1⁄2” to 12”
Pressure range: 15 to 200 psig (1 to 13.8 barg)
Temperature(max): 200°F(93°C)
LH SERIES JET PUMPS FROM Emerson Penberthy |
Size (Inches) | Emerson Penberthy PVC LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4APV |
1/2B | LH-4BPV |
1/2 | LH-04PV |
3/4 | LH-06PV |
1 | LH-08PV |
1 1/4 | LH-10PV |
1 1/2 | LH-12PV |
2 | LH-16PV |
2 1/2 | LH-20PV |
3 | LH-24PV |
4 | LH-32PV |
Size (Inches) | Emerson Penberthy HASTELLOY "C" LH (High Head) Series Eductors / Jet Pumps |
1/2A | LH-4AHC |
1/2B | LH-4BHC |
1/2 | LH-04HC |
3/4 | LH-06HC |
1 | LH-08HC |
1 1/4 | LH-10HC |
1 1/2 | LH-12HC |
2 | LH-16HC |
2 1/2 | LH-20HC |
3 | LH-24HC |
4 | LH-32HC |
Size (Inches) | Emerson Penberthy Bronze LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4ABZ |
1/2B | LH-4BBZ |
1/2 | LH-04BZ |
3/4 | LH-06BZ |
1 | LH-08BZ |
1 1/4 | LH-10BZ |
1 1/2 | LH-12BZ |
2 | LH-16BZ |
2 1/2 | LH-20BZ |
3 | LH-24BZ |
4 | LH-32BZ |
Size (Inches) | Emerson Penberthy Cast Iron LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4AIR |
1/2B | LH-4BIR |
1/2 | LH-04IR |
3/4 | LH-06IR |
1 | LH-08IR |
1 1/4 | LH-10IR |
1 1/2 | LH-12IR |
2 | LH-16IR |
2 1/2 | LH-20IR |
3 | LH-24IR |
4 | LH-32IR |
Size (Inches) | Emerson Penberthy Carbon Steel LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4ACS |
1/2B | LH-4BCS |
1/2 | LH-04CS |
3/4 | LH-06CS |
1 | LH-08CS |
1 1/4 | LH-10CS |
1 1/2 | LH-12CS |
2 | LH-16CS |
2 1/2 | LH-20CS |
3 | LH-24CS |
4 | LH-32CS |
Size (Inches) | Emerson Penberthy Stainless Steel LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4ASS |
1/2B | LH-4BSS |
1/2 | LH-04SS |
3/4 | LH-06SS |
1 | LH-08SS |
1 1/4 | LH-10SS |
1 1/2 | LH-12SS |
2 | LH-16SS |
2 1/2 | LH-20SS |
3 | LH-24SS |
4 | LH-32SS |
Size (Inches) | Emerson Penberthy Monel LH (High Head) Eductors / Jet Pumps |
1/2A | LH-4AMO |
1/2B | LH-4BMO |
1/2 | LH-04MO |
3/4 | LH-06MO |
1 | LH-08MO |
1 1/4 | LH-10MO |
1 1/2 | LH-12MO |
2 | LH-16MO |
2 1/2 | LH-20MO |
3 | LH-24MO |
4 | LH-32MO |
Jet Pumps for Pumping Liquids up to 70+ psi discharge head pressure
Operation for Penberthy Emerson Liquid Jet Pumps
All Emerson jet pumps operate on the principle of a fluid entraining a second fluid. Although design and construction may vary, this applies to all jet pumps.
All Emerson jet pumps have three common features: inlet, suction and discharge. They function as follows:
Inlet - The operating medium (liquid or steam) under pressure enters the inlet and travels through the nozzle into the suction chamber. The nozzle converts the pressure of the operating medium into a high velocity stream, which passes from the discharge side of the inlet nozzle.
Suction - Pumping action begins when vapor, gases or liquid in the suction chamber are entrained by the high velocity stream emerging from the inlet nozzle, lowering the pressure in the suction chamber. The resulting action causes the liquid, gas or vapor in the suction chamber to flow toward the discharge.
Discharge - The entrained material from the suction system mixes with the operating medium and acquires part of its energy in the parallel section. In the diffuser section, part of the velocity of the mixture is converted to a pressure greater than the suction pressure, but lower than the operating medium pressure.
Buy Penberthy Emerson LH Series Eductors HERE!
ALL Penberthy Emerson Jets can be found HERE!
All Emerson jet pumps operate on the principle of a fluid entraining a second fluid. Although design and construction may vary, this applies to all jet pumps.
All Emerson jet pumps have three common features: inlet, suction and discharge. They function as follows:
Inlet - The operating medium (liquid or steam) under pressure enters the inlet and travels through the nozzle into the suction chamber. The nozzle converts the pressure of the operating medium into a high velocity stream, which passes from the discharge side of the inlet nozzle.
Suction - Pumping action begins when vapor, gases or liquid in the suction chamber are entrained by the high velocity stream emerging from the inlet nozzle, lowering the pressure in the suction chamber. The resulting action causes the liquid, gas or vapor in the suction chamber to flow toward the discharge.
Discharge - The entrained material from the suction system mixes with the operating medium and acquires part of its energy in the parallel section. In the diffuser section, part of the velocity of the mixture is converted to a pressure greater than the suction pressure, but lower than the operating medium pressure.
Buy Penberthy Emerson LH Series Eductors HERE!
ALL Penberthy Emerson Jets can be found HERE!
Anderson-Bolds
216-360-9800
www.anderson-bolds.com
LH High Head Series Liquid Motive Emerson Penberthy Jet Pumps (Eductors)
No comments:
Post a Comment