Sunday, March 30, 2014

Q'Mark Commercial Baseboard - QMKC


QMKC SERIES ~ Electric Commercial Baseboard by Q'Mark and Anderson-Bolds
Commercial grade construction: 18-gauge front and cover brackets allow heater to withstand rigors of commercial applications. 
Easy installation: Can be installed with minimal disassembly, using mounting holes in rear of cabinet 
Built-in wireway: Facilitates end-to-end installation of continuous-run heaters 
Efficient heat dissipation: "Chimney fin" type element designed for maximum air circulation. Air flow is directed away from walls 
Steel sheathed element: Heating element design combines the durability of a steel tubular heater with the excellent heat transfer characteristics of aluminum fins 
Roomy junction box: Large, identical, pre-wired junction boxes at each end are provided with knockouts in the rear, bottom, inside and outside junction box walls 
Navajo White or Northern White durable textured polyester powder coat finish 



QMKC25126W  2.5 feet  120 volts  500 watts
QMKC25026W  2.5 feet  208 volts  500 watts
QMKC25426W  2.5 feet  240/208 volts  500/376 watts
QMKC25726W  2.5 feet  277/240/208 volts  500/375/282 watts
QMKC2513W    3.0 feet   120 volts  750 watts
QMKC2503W    3.0 feet   208 volts  750 wtts
QMKC2543W    3.0 feet  240/208 volts  750/564 watts
QMKC2573W    3.0 feet  277/240/208 volts  750/564/423 watts
QMKC2514W    4.0 feet  120 volts  1000 watts
QMKC2504W    4.0 feet  208 volts  1000 watts
QMKC2544W    4.0 feet  240/208 volts  1000/752 watts
QMKC2574W    4.0 feet  277/240/208 volts  1000/752/564 watts
QMKC2515W    5.0 feet  120 volts  1250 watts 
QMKC2505W    5.0 feet   208 volts 1250 watts
QMKC2545W    5.0 feet   240/208 volts   1250/940 watts
QMKC2575W    5.0 feet   277/240/208 volts  1250/940/705 watts
QMKC2516W    6.0 feet  120 volts   1500 watts
QMKC2506W    6.0 feet  208 volts   1500 watts
QMKC2546W    6.0 feet  240/208 volts  1500/1128 watts
QMKC2576W    6.0 feet  277/240/208 volts  1500/1128/846 watts
QMKC2508W    8.0 feet  208 volts   2000 watts
QMKC2548W    8.0 feet  240/208 volts   2000/1504 watts
QMKC2578W    8.0 feet  277/240/208 volts  2000/1504/1128 watts
QMKC25008W  12.0 feet  208 volts   2500 watts
QMKC25408W  12.0 feet  240/208 volts  2500/1880
QMKC25708W  12.0 feet  277/240 volts  2500/1880/1410

QMK CBDA2W   2'6" Blank Section
QMK CBDA3W    3' Blank Section
QMK CBDA4W    4' Blank Section
QMK CBDA5W    5' Blank Section
QMK CBDA6W    6' Blank Section
QMK CBDA8W    8' Blank Section
QMK ICAW Inside corner
FS12  1 foot filler section
FS24  2 foot filler section
FS36  3 foot filler section
FS48  4 foot filler section
FSJ2  2 inch Joiner Strip

TA1AW  SINGLE POLE THERMOSTAT, 22 amps
TA1TPAW  Tamper Resistant Single Pole Thermostat
TA2AW  DOUBLE POLE THERMOSTAT, 22 amps
TA2TPAW Tamper Resistant Double Pole Thermostat
HCA121520W 120 volt Load Transfer Switch
HCA241520W 240 volt Load Transfer Switch
RA1W  120 volt DuPlex receptacle
RA1COMPW  Duplex Receptacle cover
DSW2W   Double Pole Disconnect Switch 
PR24  Single Pole Power Relay, 24volt control, 30 amps
PR120  Single Pole Power Relay, 120 volt control, 30 amps
RSA1224  120/24V TRANSFORMER RELAY - 25A
RSA2024  208/24V TRANSFORMER RELAY - 25A
RSA2424  240/24V TRANSFORMER RELAY - 25A
RSA2724  277/24V TRANSFORMER RELAY - 25A


Navajo White or Northern White durable textured
polyester powder coat finish for corrosion resistance. Linear
thermal cut-out shall be factory installed to automatically shut
off heater in event of overheating and reactivate heater when
temperatures return to normal. Raceway cover kit for
providing an enclosed raceway is standard. The complete
heater shall have a height of 6-3/4 (171.5) inches and a
depth of 2-7/8 (73.2) inches. Heaters shall have cULus
approval for mounting on any floor surface including
carpeting.

Heating Element: The heating element wire shall consist
of 80% nickel, 20% chromium, and shall be encased in steel
sheath to assure long and trouble free life. Aluminum fins
shall be so designed as to block sheath radiation to front and
back of heater body and pressure bonded to steel sheath.

Enclosure: The heaters shall be fabricated of minimum
.024 in. steel with minimum .040 in. steel control boxes.
Support brackets shall be .035 in. steel. Junction box
enclosure to have provisions for incoming and outgoing cable
with cable clamp for restraining without additional hardware.
Ground wire pigtail provided in each junction box for
grounding.


email us at qmark@anderson-bolds.com
or call 216-360-9800








No comments:

Post a Comment