RAYMAX® 1220 and 2030 Panel Heaters from Anderson-Bolds
for a quote please email to watlow@anderson-bolds.com
or use our WATLOW form HERE!
Ideal For Many Process Heating Applications Requiring “Hot Face” Temperatures
The Raymax Panel heater product line from Watlow solves virtually an application requiring radiant heat from a contamination resistant surfaces to fast responding high temperature needs.
 |
| Watlow Raymax Radient Panel |
Maximum face temperature up to 2000ºF
Typical applications are:
Thermoforming
Food warming
Paint and epoxy curing
Heat treating
High temperature Furnaces
Tempering and annealing processes
Raymax 1010
1000ºF Face Temperature
The Ryamax 1010 is the ideal for use in screen printing, food warming and other low heat applications. The Heater's "sealed face" keeps contaminates away from the heating element, and the metal surface can be easily wiped or brushed clean whenever needed.
Uniform full surface heat source
Convenient ready to use package
One inch thick backside insulation
Repeatable temperature sensing options
UL: component listing.
Heater width is from 4-20 inches
Heater Length is from 10 to 68 inches
voltage up to 480 vac
Watt Density is 10W/sq. inch
Easy to install and capable of high surface temperatures,
the RAYMAX® 1220 and 2030 are ideal for many process
heating applications requiring “hot-face” temperatures
above 1000°F (540°C).
Each ceramic fiber heater is mounted in a 21⁄2 in. (64 mm)
deep sheet metal case providing thermal insulation. The case
includes post terminals for electrical connections and
provides a mounting system that can be used with virtually
any flat ceramic fiber unit. Watt density and temperature
capabilities can be tailored to meet a specific radiant
application for exposed sinuated embedded coil or foil
element configuration.
Performance Capabilities
• RAYMAX 2030 (uses sinuated or coil elements):temperatures up to 2000°F (1095°C); watt densitiesup to 30 W/in2 (4.7 W/cm2)
• RAYMAX 1220 (uses an etched foil element):temperatures up to 1200°F (650°C); watt densitiesup to 20 W/in2 (3 W/cm2)
• Maximum voltage up to 600V
Features and Benefits
Lightweight, low mass design
• Allows fast response to controllers
Self insulation with 21/2 in. (64 mm ) thick mounting case
• Provides high efficiency
Thermocouple mounting clamp
• Simplifies process system control
Aluminized steel case
• Handles temperatures up to 1100°F (595°C)
Special hot-face heating patterns
• Designed specifically for an application using an etched foil RAYMAX 1220
Specifications
Weight: Less than 6.5 lbs/ft2 (31.75 kg/m2)
Voltage and Wattage: Ratings, up to 600VAC are based on
the ceramic fiber heater module mounted in the case.
Terminals: Terminals are 1⁄4-20 threaded studs. Two terminals
plus ground for single-phase, and three terminals plus ground
for 3-phase are located on the center length line unless
otherwise specified. Terminals can be positioned anywhere
along lines A and B (see illustration below), but not closer
than 2 in. (51 mm) to the case ends.
Mounting Legs: Mounting legs are available either
1 in. (25 mm) or 3 in. (76 mm) length. For made-to-order units,
mounting legs can be supplied in any incremental length L
from 1⁄2 in. (13 mm) to 3 in. (76 mm). Slots are not provided in
legs less than 1 in. (25 mm) long.
Application Hints
A thermocouple mounting clamp is attached to one end of
the case, with holes on both ends for alternate locations.
The clamp can be used with 1⁄8 in. (3.2 mm) O.D. sheath
thermocouples. The clamp is 3/16 in. (4.8 mm) high, but
can be removed for flush mounting*.
The maximum recommended surface temperature of the
heater is based on the rating of the ceramic fiber heater
module. This can vary from 2000°F (1095°C) at lower watt
densities, to higher watt densities at reduced surface
temperatures. Note: maximum wattages cannot be achieved
at the maximum temperatures simultaneously.
* 13⁄16 in. (4.8 mm) and 1⁄4 in. (6 mm) are available upon request.
Options
Several options are available with RAYMAX 1220 and 2030
models. Contact your Watlow representative for more
information.
• Single-phase non-standard location power terminals
• Terminal box
• Zoning
• Mounting studs and legs
• 3-phase construction
• Thermocouple mounting tubes
• Alternate case materials
RAYMAX 2030 PART NUMBERS
VP504A06T, VP504A12T, VP504A18T, VP504A24T, VP504A30T, VP504A36T
VP506A06T, VP506A12T, VP506A18T, VP506A24T, VP506A30T, VP506A36T
VP508A06T, VP508A12T, VP508A18T, VP508A24T, VP508A30T, VP508A36T
VP510A06T, VP510A12T, VP510A18T, VP510A24T, VP510A30T, VP510A36T
VP510A06T, VP510A12T, VP510A18T, VP510A24T, VP510A30T, VP510A36T
VP512A06T, VP512A12T, VP512A18T, VP512A24T, VP512A30T, VP512A36T
VP514A06T, VP514A12T, VP514A18T, VP514A24T, VP514A30T, VP514A36T
VP516A06T, VP516A12T, VP516A18T, VP516A24T, VP516A30T, VP516A36T
Anderson-Bolds
216-360-9800
