Tuesday, June 25, 2013

Grieve Walk-In Ovens for Industrial Applications



Grieve Ovens, in business for over 50 years, is in the business of manufacturing the best industrial ovens in the USA.  Build in Illinois and completed tested, the Grieve oven will meet the test of time for your application for years to come.
Ovens and furnaces for which there simply are no equals...Grieve.

Walk In Ovens are used for paint baking, drying, preheating, annealing or any other heat processing of large or numerous parts at temperatures to 750°F. Oven size conveniently accommodates materials handling equipment. Choice of either combination or full horizontal air flow in either rear or top mounted heat chamber configurations. Designed and constructed for long, hard, continuous use.
Every oven fully assembled and individually factory tested 
STANDARD FEATURES
UL ul1.gif LISTED CONTROL PANEL 
Standard Truck Ovens from Grieve meet the requirements of National Fire Protection Association Standard 86, Industrial Risk Insurers, Factory Mutual and OSHA standards. For some applications, such as those involving flammable solvents or hazardous locations, the above organizations require additional safety devices.

Controls
— Digital, microprocessor based, thermocouple actuated, indicating temperature controller
— Modulating burner on gas ovens
— Motor control push buttons and on-off heat switch
— LED pilot lights
Safety Equipment — Electric Oven
— Adjustable, thermocouple actuated, manual reset excess temperature interlock
— Separate heating element control contactors
— Recirculating blower air flow safety switch
Safety Equipment — Gas Oven
—Adjustable, thermocouple actuated, manual reset excess temperature interlock
—Electronic flame safeguard protection
—Powered forced exhauster for combustion venting
—Exhauster air flow safety switch
—Recirculating blower air flow safety switch
—Two pilot safety shutoff valves with leak test stations
—Two main safety shutoff valves with leak test stations (Industrial Risks Insurers vent valve only provided on specific request)
—Valve position indicator on main safety shutoff valves
—Over 400,000 BTU/HR safety shutoff valve interlocked with
purge timer
—Purge timer
—High gas pressure switch
—Low gas pressure switch
Construction
—Choice of air flow patterns
—Adjustable opposed louvers on full coverage supply and return
duct work
—Choice of rear or top heat chamber
—Available with doors at each end
—Choice of floor configurations, flat plate, insulated floor, truck
wheel guide tracks
—Exceptionally heavy duty doors
—Aluminized steel interior
—Aluminized steel exterior with enamel finish
—High temperature door gasket with stainless steel spring insert
—6 lbs/cf density industrial rockwool insulation
—Brushed stainless steel control panel face
—1 year limited warranty
Every oven fully assembled and individually factory tested 


Combination Air Flow
Heated air is provided from full coverage supply duct work at each side of the work space and sweeps upward through the load to a return duct at the top of the work space. Used in most shelf truck loading applications where sufficient shelf area is left open to allow vertical air movement upward through the loaded truck. Ideal for large parts placed directly on oven floor or loaded on a flat bed truck. 

Horizontal Air Flow
Heated air is blown horizontally across the work space between full coverage duct work. For shelf truck loading applications with densely loaded shelves, solid bottom trays, or flat sheets where heated air can only pass sideways above and below each level. Also used on oven floor or loaded on a flat bed truck. 

Electric Models
Each features completely wired, side access UL listed control panel enclosing terminals for incoming power, temperature controllers, push buttons and pilot lights. Motor starter and heating element contactors electrically interlocked to shut off heaters if power to blower is interrupted and to permit operation of blower without heat for cooling. Incoloy sheathed tubular heating elements.

Gas Models
— 1,000 BTU natural gas at 6" water column pressure: 1" NPT inlet to 350,000 BTU/HR; 1-1/4" NPT to 1,200,000 BTU/HR

Anderson-Bolds represents the Grieve Oven Corporation throughout Ohio and Kentucky.

email us at grieve@anderson-bolds.com
216-360-9800

Other industrial products are found at www.anderson-bolds.com

Saturday, June 1, 2013

Elster American Meter Gas Meters ~ Stock at Anderson-Bolds

Call Anderson-Bolds or order online for Elster American Meter Gas Meters and Regulators.

216-360-9800 ask for Jerry or email to amco@anderson-bolds.com

AMCO = American Meter Company

Below units are usually stocked at Anderson-Bolds


DTM-200A-1      AMCO DRY TEST METER
DTM-200A-2      AMCO DRY TEST METER





AM-250-5#TC         AMCO METER, TC, 5#

AL-800-20#TC        AMCO AL-800, 20# WP, TEMP COMP

AL-425-25#TC        AMCO AL-425, 25# WP, TEMP. COM

AL-425-25#             AMCO METER, 1-1/4, W/ODOMETER

AL-425-10#TC        AMCO AL-425, 10#WP, TEMP. COMP

AC-630-25#TC       AMCO AC-630 METER, 25#, TC

AC-250-5#TC          AMCO AC-250, 5# WP, TEMP. COMP

AC-250-10#TC       AMCO METER, 1", ODOMETER INDEX





2M-CID-2"                           AMCO RPM METER WITH instrument Drive

2M-MTCI-2"-TWELL       AMCO 2" 3.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

3.5M-CTR-2"-TWELL       AMCO 3.5M RPM WITH TWELL, 80 MESH SCREEN, BOLT/GSKT SET

3.5M-MTCI-2"-TWELL    AMCO 2" 3.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

5.5M-CTR-2"-TWELL       AMCO 5.5M RPM W/TWELL  80 MESH SCREEN, BOLT/GSKT SET

5.5M-CTR-3"-TWELL       AMCO 3" 5.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

5.5M-MTCI-3"-TWELL    AMCO 3" 5.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET




Anderson-Bolds also has Elster American Meter Company regulators and parts.

Along with Gas meters, Anderson-Bolds carries Water meters and Flow Meters.

216-360-9800 (Jerry)
www.anderson-bolds.com