American Meter 1813C Regulators

Anderson-Bolds Stocks American Meter Series 1813C Regulators

The Elster American Meter 1800C Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide, propane vapor, and other non-corrosive gases in residential, light commercial, and small industrial applications.

General Information

Outlet pressures between 3.5" W.C. and 2 PSIG are available. Operating temperature range is -20°F to 150°F (-30°C to 65°C). Maximum flow rate is 2500 SCFH (70.8 m3/h).

All models conform to ANSI Code B109.4-1998, and CGA Service-Type Regulator Specification CAN/CGA-6.18-M95. 

Features

• Variety of interchangeable orifices and spring ranges

• 90 Degree (Right Angle), 180 Degree (Straight-Flow), or Offset Valve Body 

(See photo below)

• Wide range of valve body connection sizes 

Options:

Vent Elbow

The regulator vent opening should face downward (6 o'clock) to minimize the chance of blockage from ice and snow. If not possible, a 3/4" NPT plastic, 90° vent elbow (part number 78041P025) and separate protective screen (part number 70400P017) may be screwed into the vent to provide the necessary protection.

Elevation Compensation

The E.C. orifice is recommended for installations where the inlet pressure may vary over a wide range. The E.C. orifice is available in two sizes: 1/8" x 3/16" and 3/16". The capacities of these orifices are the same as the standard orifice of the same size.

Full Capacity Relief Valve Full capacity internal relief valve standard on all models. (See Performance Graphs on page 9)

SplashguardsUV stabilized, weather-resistant, resin device that protects the vent screen from splashes while providing a large external vent opening to keep regulators working properly.

Safety Shutoff Devices Overpressure Shutoff (OPSO) — Operates independently. The OPSO will shut off the gas supply in the event of a serious downstream pressure build-up. These are available in two pressure ranges on the Models 1843C and 1843C-HC.

When the outlet pressure exceeds the OPSO set point, the pressure under the OPSO diaphragm (A) compresses the pressure spring (B) forcing the diaphragm stem (E) upwards and releasing plunger (D). This permits the shut-off spring (F) to force the shut-off disc (G) against the back side of the special double-ended orifice.

Universal Safety Shutoff Assembly (USSA) — USSA protects the downstream piping from both over- and under-pressure conditions by shutting off the gas flow at the inlet side of the regulator orifice. Both Over- and under-pressure shut-off set points are adjustable depending on spring ranges selected.

To Buy, please click on the unit below


Elster American Meter 3/4 NPT model 1813C GAS regulator with 3/16 orifice, 6-15 WC spring

Elster American Meter 1 NPT model 1813C gas regulator with 1/8x3/16 orifice, 6-15 WC spring

Elster American Meter 1 NPT model 1813C gas regulator with 3/16 orifice, 6-15 WC spring

Elster American Meter 1 NPT model 1813C gas regulator with 5/16 orifice, 6-15 WC spring

Elster American Meter 1 NPT model 1813C gas regulator with 3/8 orifice, 6-15 WC spring

Elster American Meter 1 NPT model 1813C gas regulator with 9/16 orifice, 6-15 WC spring

Elster American Meter 1-1/4 NPT model 1813C gas regulator with 9/16 orifice, 6-15 WC spring





Anderson-Bolds
216-360-9800
www.anderson-bolds.com

Process Ovens Over 40 years Old

Anderson-Bolds and Grieve Ovens

Safety Updates for Older Ovens.

 
Most Process ovens made over 40 years ago did not include an excess temperature controller or separate heating element contactors to protect the oven from overheating if the main temperature controller or contactors fail.  Any ovens like this should not be used until this safety equipment is installed.  Failure to install this safety equipment could result in the oven overheating and a fire that could result in oven damage, loss of the product load, building damage and injury to personnel.
 
A field kit to add the excess temperature controller and separate contractors should be ordered from the MFG.

The excess temperature controller and separate contactors are now standard equipment on all Grieve ovens.  Also standard is a recirculating blower airflow safety switch to shut down the oven heat if the recirculating blower fails.  This is a pressure differential switch that senses the pressure created when the blower wheel is turning.  This switch protects the oven heating elements by preventing them from heating when air is not being recirculated over them.  A field kit for installation of the recirculating blower airflow safety switch should be purchased from the oven MFG.

When installing new safety equipment it can be a good idea to add other new electronics to the oven for better performance.  New electronics could be a digital temperature controller, programmable digital temperature controller, new thermocouples or a digital timer.  Grieve can provide a field kit to add a digital temperature controllers as well as and a field kit for a digital shut down timer. For electric Ovens new elements can be ordered as well along with pin and sleeve disconnect switches for added electrical safety for personnel. We can provide Gas meters for gas ovens to measure gas flow at the oven and shut the oven down in a dangerous situation.

Grieve's field kits include installation instructions, wiring diagram showing items to be removed, wiring diagram showing items to be added and revised wiring diagram for your records.  Our kits will be based on how the ovens were constructed when they left our factory.  If there have been changes made to the oven in the field they will not be included in our revised wiring diagram.   

Grieve will provide all parts except for standard wire, conduit and conduit fittings.  These items are better provided in the field as necessary to connect the components being added.  Conduit would only be required for the air flow safety switch as the other items are mounted in the oven control panel.

Please contact Anderson-Bolds with the oven serial number, job # and model number all of which can be found on the name plate of the oven.  We can also provide new wiring schematics for old ovens and instruction manuals.  Grieve and Anderson-Bolds want our products to be operated in the safest manner possible. 

Meltric deContactor Plugs

Elster American Meter Gas Meters

Watlow Temperature Controllers

Contact Anderson-Bolds at:

216-360-9800 

grieve@anderson-bolds.com

AMCO Meters in Stock at Anderson-Bolds

Anderson-Bolds AMCO Elster American Meter stock for 24 hour shipment.
Both Meters and Regulators are in stock.
We also stock springs, orifices, mesh, gasket sets, screens, filter elements and sleeves.
Meters can be ordered ONLINE HERE.

Elster American Meter (AMCO) Gas Meters and Gas Regulators from Anderson-Bolds

Buy AMCO Gas Meters HERE.

Buy AMCO Gas Regulators HERE.

17709G013	AMCO RABO THERMOWELL
1803/1-1/2	AMCO REGULATOR, 1-1/2"
1803/2	AMCO REGULATOR, 2"
1813B/1.5	AMCO REGULATOR 1813B, 1.5"
1813B/2	AMCO REGULATOR, 2X2
1813C114916615	AMCO 1-1/4" REGULATOR, 9/16"
1813C118316615	AMCO 1813C 1", 1/8X3/16" ORF.
1813C1316615	AMCO 1813C 1", 3/16" ORF.,
1813C138615	AMCO 1813C 1", 3/8" ORF.,
1813C1516615	AMCO 1813C 1", 5/16" ORIFICE,
1813C1916615	AMCO 1813C 1", 9/16" ORF.
1843C-3/4 1/4" 12-28	AMCO REGULATOR, 3/4"
2M-TRVP-2	AMCO 2M RPM WITH TC, AND
3.5M-RABO-2"-80M/B	AMCO RABO 2" METER W/ 80 MESH
3.5M-TRVP-2	AMCO 3.5M WITH TC, AND
AC-250-5#TC	AMCO AC-250, 5# WP, TEMP. COMP
AC-630-25#TC	AMCO AC-630 METER, 25#, TC
AC-800-25#TC	AMCO AC-800 METER, 25#TC
AL-425-10#TC	AMCO AL-425, 10#WP, TEMP. COMP
AL-425-25#TC	AMCO AL-425, 25# WP, TEMP. COM
AM-250-5#TC	AMCO METER, TC, 5#
J48-1"	JEAVONS REG, 1"
J48-1-1/4	AMCO REGULATOR
J78RS-1/2"	AMCO REG TYPE J78, 1/2", 4-8"
J78RS-3/4"	AMCO REGULATOR, 3/4",

For Parts please call Anderson-Bolds or email to amco@anderson-bolds.com


www.anderson-bolds.com
216-360-9800 ask for Jerry

Elster American Meter Gas Meters ~ Stock at Anderson-Bolds

Call Anderson-Bolds or order online for Elster American Meter Gas Meters and Regulators.

216-360-9800 ask for Jerry or email to amco@anderson-bolds.com

AMCO = American Meter Company

Below units are usually stocked at Anderson-Bolds

DTM-200A-1      AMCO DRY TEST METER

DTM-200A-2      AMCO DRY TEST METER

AM-250-5#TC         AMCO METER, TC, 5#

AL-800-20#TC        AMCO AL-800, 20# WP, TEMP COMP

AL-425-25#TC        AMCO AL-425, 25# WP, TEMP. COM

AL-425-25#             AMCO METER, 1-1/4, W/ODOMETER

AL-425-10#TC        AMCO AL-425, 10#WP, TEMP. COMP

AC-630-25#TC       AMCO AC-630 METER, 25#, TC

AC-250-5#TC          AMCO AC-250, 5# WP, TEMP. COMP

AC-250-10#TC       AMCO METER, 1", ODOMETER INDEX

2M-CID-2"                           AMCO RPM METER WITH instrument Drive

2M-MTCI-2"-TWELL       AMCO 2" 3.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

3.5M-CTR-2"-TWELL       AMCO 3.5M RPM WITH TWELL, 80 MESH SCREEN, BOLT/GSKT SET

3.5M-MTCI-2"-TWELL    AMCO 2" 3.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

5.5M-CTR-2"-TWELL       AMCO 5.5M RPM W/TWELL  80 MESH SCREEN, BOLT/GSKT SET

5.5M-CTR-3"-TWELL       AMCO 3" 5.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

5.5M-MTCI-3"-TWELL    AMCO 3" 5.5M RPM W/MERCURY TCI, 80 MESH SCREEN, BOLT/GSKT SET

Anderson-Bolds also has Elster American Meter Company regulators and parts.

Along with Gas meters, Anderson-Bolds carries Water meters and Flow Meters.

216-360-9800 (Jerry)
www.anderson-bolds.com

ERDCO series 3200 See-Flo Indicator

Anderson-Bolds and ERDCO Flow Meters

ERDCO 3200 See-Flo® Indicator

See-Flo® meters indicate flow rate and permit visual inspection of water, air or other transparent fluids. For general purpose industrial service, See-Flo® meters handle a wide range of process fluids in vertical or horizontal piping runs.

The wedge shape of the meter housing makes See-Flo® practically self-cleaning. Where periodic maintenance might be necessary, the tempered glass window is easily removed and replaced. Because of its large internal cavities this product will not plug up like the old glass tube "rotameters".

Each flowmeter is calibrated to be direct reading for the liquid or gas operating conditions that you specify. Scales with special engineering units and dual units of measure are available.

PLEASE NOTE THE THE SEE_FLO METER NEEDS TO BE ORDERED BASED ON DIRECTION OF FLOW.  Right to Left, Left to Right, Up or Down. The meter will not work properly if ordered incorrectly. Please specify when ordering.

Applications: Transparent Liquid or Gases

Functions: Direct Reading flow rate and Observe fluid condition

Features: Lowest Cost Meter; No power required; Calibrated for application conditions

Materials: Aluminum, brass or 316 stainless steel

Pressure Limit:  200 psig

Temperature Limit: 400ºF (400 requires Viton or EPM O-rings)

Pipe Sizes: 1/2 to 12 inches

Ideal for use with water containing solid particles (up to 1/4" dia.) that clog conventional meters, these flowmeters have a 17-7 PH stainless steel vane inside the flowmeter that moves in proportion to flow rate. There are no floats that could stick and no tubes to clean. Scale is graduated in gallons per minute. Flowmeters have a brass body (unless noted) and EPDM O-rings. Maximum pressure is 200 psi at 70° F. Temperature range is -10° to +400° F. 

Below are common Flow meters, but ERDCO and Anderson-Bolds can do many combinations of size, flow, body material, seal material and flow direction.

Flow Range (gpm)	SIZE	MC   p/n	ERDCO p/n
0.5 – 5 gpm	½”	4165K112	3221-02T0-11 / .5-5
1 - 10 gpm	½”	4165K122	3221-02T0-11 / 1-10
1.5 – 15 gpm	¾”	4165K132	3221-03T0-11 / 1.5-15
2 – 20 gpm	1”	4165K142	3221-04T0-11 / 2-20
5 – 50 gpm	1”	4165K152	3221-04T0-11 / 5-50
15 – 150 gpm	1-1/2”	4165K162	3221-06T0-11 / 15-150
25 – 250 gpm	2”	4165K172	3221-08T0-11 / 25-250
30 – 300 gpm	3”	4165K182	3221-12T0-11 / 30-300
HORIZONTAL	LEFT  to	RIGHT	DIRECTION

Flow Range (gpm)	SIZE	MC   p/n	ERDCO p/n
0.5 – 5 gpm	½”	4165K113	3222-02T0-11 / .5-5
1 - 10 gpm	½”	4165K123	3222-02T0-11 / 1-10
1.5 – 15 gpm	¾”	4165K133	3222-03T0-11 / 1.5-15
2 – 20 gpm	1”	4165K143	3222-04T0-11 / 2-20
5 – 50 gpm	1”	4165K153	3222-04T0-11 / 5-50
15 – 150 gpm	1-1/2”	4165K163	3222-06T5-11 /15-150
25 – 250 gpm	2”	4165K173	3222-08T5-11 /25-250
30 – 300 gpm	3”	4165K183	3222-12T5-11 /30-300
HORIZONTAL	RIGHT  to	LEFT       FLOW	DIRECTION

Flow Range (gpm)	SIZE	MC   p/n	ERDCO p/n
0.5 – 5 gpm	½”	4165K114	3223-02T0-11 / .5-5
1 - 10 gpm	½”	4165K124	3223-02T0-11 / 1-10
1.5 – 15 gpm	¾”	4165K134	3223-03T0-11 / 1.5-15
2 – 20 gpm	1”	4165K144	3223-04T0-11 / 2-20
5 – 50 gpm	1”	4165K154	3223-04T0-11 / 5-50
15 – 150 gpm	1-1/2”	4165K164	3223-06T5-11 / 15-150
25 – 250 gpm	2”	4165K174	3223-08T5-11 / 25-250
30 – 300 gpm	3”	4165K184	3223-12T5-11 / 30-300
VERTICAL	UP é	FLOW	DIRECTION

Flow Range (gpm)	SIZE	MC   p/n	ERDCO p/n
0.5 – 5 gpm	½”	4165K115	3224-02T011 / .5-5
1 - 10 gpm	½”	4165K125	3224-02T011 / 1-10
1.5 – 15 gpm	¾”	4165K135	3224-03T011 / 1.5-15
2 – 20 gpm	1”	4165K145	3224-04T011 / 2-20
5 – 50 gpm	1”	4165K155	3224-04T011 / 5-50
15 – 150 gpm	1-1/2”	4165K165	3224-06T011 / 15-150
25 – 250 gpm	2”	4165K175	3224-08T011 / 25-250
30 – 300 gpm	3”	4165K185	3224-12T011 / 30-300
VERTICAL	DOWN ê	FLOW	DIRECTION

Please note,  SEE-FLO METERS can come in gpm ranges specified to your specific application.

Also the connection type can be any of the following:

NPT END
NPT BACK
TRI-CLAMP
GROOVED
BEVELED
SOCKET (1/2 - 1 inch)
FLANGE (150#RF)
FLANGE (150#FF)
FLANGE (300#RF)
FLANGE (300#FF)
FLANGE (DIN PN16)
BSPT End
BSPT Back


ERDCO®  ENGINEERING  COMPANY offers a complete line of flowmeters, sight flow indicators, flow transmitters and flow indicating switches. We employ elegantly simple measuring technologies with proven reliability in utility fluid applications.
Whether it's chilled water, air, nitrogen, steam, lube oil or other process support fluid, ERDCO has the flow measurement solution. Select from in-line and insertion styles that feature simplicity, rugged construction and reliable operation. This product range has great versatility across a broad set of applications.


Contact Anderson-Bolds at 216-360-9800 or via our CONTACT FORM
Ask for Jerry for your ERDCO Flow Meter needs and questions.
ERDCO Meters On Anderson-Bolds