Tuesday, August 13, 2019

ATEX Robertshaw EURO366 Vibration Switch

Anderson-Bolds Sells the Robertshaw EURO 366 VIBRASWITCH

Click HERE for the Robertshaw Vibration Switch Matrix


by Schneider Electric and Robertshaw Industrial

  •  Flame Proof (Explosion Proof )
    EEx d IIB/C T6 IP66 T85°C - CESI 03 ATEX 186

  •   Self Powered
    Does not require any form of external power to operate.

  •   Acceleration Sensitive
    Measures total destructive shock, not displacement.

  •   Minimum Maintenance
    No moving parts except when set-point is exceeded.

  •   Continuous Protection
    No attention required after installation.

  •   Ease of Installation
    Requires no special training.

  •   Long Life
    Instrument is rugged and durable - no wearing parts.

  •   Reset
    Manual at unit and choice of remote electrical.

  •   AC or DC
    Reset coil options.

  •   IP66 Enclosure For outdoor and indoor use. 

    EURO366 from Robertshaw

The EURO366 Vibraswitch malfunction detector provides maximum protection from rotating and reciprocating of large motors, pumps or compressors. It is intended for indoor or outdoor use in hazardous or non-hazardous areas with ATEX and CE certifications.

The Model EURO 366 VIBRASWITCHis primarily intended for indoor and outdoor hazardous and non- hazardous areas in those countries requiring ATEX and CE certifications. The EURO 366 employs the same time proven switch design found in Robertshaw's family of vibration switches.

The Model EURO 366 VIBRASWITCHis a vibration sensitive device that protects rotating and reciprocating machinery from extensive damage resulting from mechanical malfunction.When the vibration level of a VIBRASWITCH protected machine exceeds normal by a preselected amount, the normally open contacts of an internal switch close and the normally closed contacts open. This can be used to actuate either an audible warning system or a shutdown circuit before costly damage occurs

Failing bearings, broken blades and similar malfunctions cause increased imbalance or high frequency vibration detectable with the VIBRASWITCH. It is designed for maintenance-free service in permanent installations.

The VIBRASWITCHis an acceleration sensitive instrument that measures the total acceleratory shock present on the machine. Acceleration is a vibration characteristic of prime importance in cases of mechanical failure on reciprocating or rotating machinery. Acceleration is directly related to the shock forces (impact) acting on a machine - thus the VIBRASWITCHoffers a valid measurement of the destructive forces acting on the machine.

Accelerator measurements made by the VIBRASWITCHare the summation of all of the individual accelerations giving a total destructive force acting on the machine - the result is positive protection. 

..................... Cast aluminum UNI 4514 alloy 
Weight .......................  2.2 kg (4.9 lb) 
Enclosure Classification........ Flame (Explosion) proof
       EEx-d-IIA/B/C-T6 IP66 T85
Flame Proof Certification.........ESI 03 ATEX 186 
Enclosure Protection................IP66 Standard 
Enclosure Sealing ..................Neoprene o-ring 
Enclosure Finish......... Polyurethane painted olive drab 
Mounting Location.......... Outdoors, unprotected 
External Bolts ................ Stainless steel 
Nameplate .................... Stainless steel 
Conduits .......................2 x 3/4" UNI 6125-74 (will accept 3/4 NPT fitting) 
Ambient Temperature Limits .......... -30C to +85C (-22F to +185F) 
Humidity .............................. To 95% relative humidity @ 37.7C (100F) 
Shock ...................................... 40 g @ 11 ms maximum 

Vibration Measurement Range (Peak)

   Mounted Horizontal....0 to 4.5 g from 0 to 300 Hz
   Mounted Vertical........0 to 3.5 g from 0 to 300 Hz 
Set Point Adjustment ................................. 1 turn per g 
Accuracy ..............5% of full range from 0 to 300 Hz 
Ambient Temperature Effect ........10%/55.5C /(132 F) maximum 

Common Part Numbers are:
↑Above switches are SPDT
↓Below Switches are DPDT

CONTACT Anderson-Bolds - info@anderson-bolds.com


Thursday, August 8, 2019

Submersible Valves from co-ax

Anderson-Bolds Sells co-ax® Submersible valves


To request a quote from Anderson-Bolds, please use our Valve Parts Form HERE!

Valve failure is a persistent threat to valve manufacturers and their customers when it comes to submerging a valve in water, particularly in seawater. The consequences are much worse compared to standard installations that can be more easily reached. Given the challenges that sub-marine environments present such as difficult access, valve corrosion and frequent maintenance, the submersible co-ax® valves are engineered for high cycle and fast actuation plus long, reliable and leak-free performance in aggressive environments.

co-ax® submersible coaxial valve

Submersible co-ax® valves meet performance, safety and reliability expectations in deep water and harsh environments and are designed for depths of 50 feet and deeper upon request. co-ax® valves inc. has been the leader in valve technology for almost 60 years and continues to develop ways to innovative and handle the most specific and difficult applications. Companies throughout the industry have used co-ax® valves in harsh marine environments and continue to trust our dependability in the most demanding valve applications.

For us and co-ax®  to help design a valve, please click HERE!

If your present valves cannot function in your application, chances are co-ax® valves will work!


Wednesday, July 31, 2019

ATC CP Percentage Timers

Anderson-Bolds sells ATC Percentage Timers, Type CP

When Timing is Everything.

Process engineers and machine designers alike turn to the Automatic Timing & Controls division of Marsh Bellofram (ATC) for their industrial timing and control requirements. These highly rugged, high-reliability products are engineered to provide accurate and repeatable timing and monitoring operations in all types of industrial environments, including factory automation, food processing, plastics, packaging, water treatment and many OEM applications. The ATC product family has recently expanded to include 1/16 DIN timers, TC/PID controllers, electromechanical timers, counters, solid state cube and plug-in timers, and time delay relays (TDR).
ATC CP Percentage timer

ATC Percentage Timers are available in several models including the Model CP single circuit repeat cycle timer is a continuous cycling control where the ON or circuit closure time is dial adjusted for a percentage of the total time cycle
About the CP Series Percentage Timer from the Automatic Timing and Controls division of Marsh Bellofram Corporation: For continuous ON-OFF control of electrical circuits, the Model CP Series Percentage Timer is a single circuit repeat cycle timer, offering continuous cycling control where the ON or circuit closure time is dial adjusted for a percentage of the total time cycle.
Applications: Control of pumps, blowers, filters, heating equipment, industrial ovens, laboratory equipment and wherever ON or OFF control is desired as a percentage of the primary fixed total time cycle.
  • Precise Fool-proof Operating Mechanism
  • Eliminates All Engaging Cams And Latches
  • Five Time Ranges From Which To Choose
  • Minimal Panel Space Needed
Click below to purchase or review the specifications.

ATC Percentage Timer, Type CP, 30 second, 120 volts AC

ATC Percentage Timer, Type CP, 60 second, 120 volts AC

ATC Percentage Timer, Type CP, 15 Minute, 120 volts AC

ATC Percentage Timer, Type CP, 30 Minute, 120 volts AC

ATC Percentage Timer, Type CP, 60 Minute, 120 volts AC

Click HERE for the catalog Sheet pdf

Cleveland, Ohio

Tuesday, May 28, 2019

Watlow F4T Process Controller

The F4T High End Watlow Process Controller from Anderson-Bolds

BUY the Watlow F4T HERE!

Watlow F4T Process Contoller

The Watlow F4T with INTUITION temperature & process controller offers a wide range of field removable I/O modules for maximum design flexibility. Configurations can be custom tailored to meet the scaling needs of a tremendous range of equipment and applications while providing exactly the hardware types required for compatibility. The F4T controller also features a 4.3 inch, color, graphical touch panel. Combining power, flexibility and functionality, this new controller offers unmatched versatility, and its best-in-class ease of use could very well make user manuals a thing of the past.
The F4T's batch processing feature can help with regulatory compliance, achieving data integrity in the plant, reducing warranty exposure, and even avoiding a potential recall scenario without significantly raising production costs. Download the specification sheet below to learn more.

Features and Benefits
4.3-inch, color touch panel with high-resolution, graphical
Shortens learning curve and reduces operator errors
Allows channels, profiles, alarms, inputs and outputs to be
personalized with user defined names
Temperature PID, data logger, trend chart,
over/under-temperature limit, power switching,
math, logic, timers and counters combined into an
integrated system
Lowers ownership costs
Eliminates the need for separate discrete components
Reduces complexity
Simplifies design, ordering and installation
Saves money
Robust algorithms for temperature, cascade, altitude,
humidity and compressor
Improves process control
Offers one to four channels of control
Provides multiple PID sets
Enables TRU-TUNE(R)+ adaptive control algorithm
Offers 40 ramp and soak profiles with real-time clock and

battery backup

COMPOSER® graphical configuration PC software
Speeds up and simplifies commissioning
Archives and documents controller setup

Connects with controller easily via Ethernet

Batch processing with bar code data entry
Easily collects and manages data records
Inputs information from bar code scan for fast and easy
data entry
Offers foolproof processing via smart profile to part linkage
Provides data security through password and data log
encrypted file options
Improves manufacturing robustness via reminder screens
ensuring all data is entered during processing
Helps ensure compliance with growing regulations and
minimizes warranty exposure
Eliminates part processing skips or walk arounds due to
improved quality control
Produces formatted data record report for easy receipt or

record management uses

Many communications options available including Ethernet
Modbus® TCP and SCPI and EIA-232/485 Modbus® RTU
Offers two USB host ports and one device port
Simplifies file transfers
Connects easily
Modular design
Adapts quickly to evolving requirements
Offers numerous types of field pluggable modules for
maximum flexibility and easiest compatibility
Features scalable and modular firmware functions
Delivers scalable input/output quantities from 1 to 36
Agency certifications include UL®, FM, CE, RoHS, W.E.E.E.,
Ensures high quality and reliability
Verifies performance in installations worldwide
SERIES F4S/F4D/F4P backward compatible
Provides easy retrofit with minimum pain and disruption
Ensures proper fit in existing SERIES F4 panel cutout
Off-the-shelf solution
Provides cost-effective “make versus buy”
Offers preconfigured touch-panel screens

Assures quicker time to market

Common Specifications
Line Voltage/Power
• Data retention upon power failure via nonvolatile memory
Functional Operating Range
• Type J: -346 to 2192ÅãF (-210 to 1200ÅãC)
• Type K: -454 to 2500ÅãF (-270 to 1371ÅãC)
• Type T: -454 to 750ÅãF (-270 to 400ÅãC)
• Type E: -454 to 1832ÅãF (-270 to 1000ÅãC)
• Type N: -454 to 2372ÅãF (-270 to 1300ÅãC)
• Type C: 32 to 4200ÅãF (0 to 2315ÅãC)
• Type D: 32 to 4200ÅãF (0 to 2315ÅãC)
• Type F: 32 to 2449ÅãF (0 to 1343ÅãC)
• Type R: -58 to 3214ÅãF (-50 to 1767ÅãC)
• Type S: -58 to 3214ÅãF (-50 to 1767ÅãC)
• Type B: 32 to 3300ÅãF (0 to 1816ÅãC)
• RTD (DIN): -328 to 1472ÅãF (-200 to 800ÅãC)
• Process: -1999 to 9999 units
Calibration Accuracy
• Calibration accuracy and sensor conformity: Å}0.1% of
span, Å}1ÅãC at the calibrated ambient temperature and
rated line voltage
• Types R, S, B: Å}0.2%
• Type T below -50ÅãC: Å}0.2%
• Calibration ambient temperature at 77ÅãF Å}5ÅãF (25ÅãC Å}3ÅãC)
• Accuracy span: 1000ÅãF (540ÅãC) min.
• Temperature stability: Typical Å}0.1ÅãF/ÅãF (Å}0.1ÅãC/ÅãC) rise in
ambient max.
Configuration Diagnostics
• Indicates if modules present match the expected
configuration settings
USB Host Port
• Total of 2 available
• Version: USB 2.0 hi-speed
• Connector: USB Type A, high-retention
• Flash drive must be FAT32 file system
• Max. current 0.5A/port
System Configuration Requirements
• F4T has 6 slots for flex modules (FM)
• EIA-232/485 Modbus(R) RTU flex module, if used, must occupy
slot 6 location
• A maximum of two 10A SSR FM modules can be used in the F4T
and each will require space for 2 slots. Valid in slots 1, 2, 4 or 5
Wiring Termination—Touch-Safe Terminals
• Right-angle and front-screw terminal blocks for input, output
and power supply connections
• Input, output and power terminals: touch safe, removable,

12 to 30 AWG

F4T Base Specifications
Line Voltage/Power
• High voltage option: 100 to 240VAC +10/-15%, 50/60Hz Å}5%
• Low voltage option: 24 to 28VAC/VDC+10/-15%, 50/60Hz Å}5%
• Power consumption: 23 W, 54VA
• NEMA 4X/IP65 front panel mount configuration only
• Operating temperature: 0 to 122ÅãF (-18 to 50ÅãC)
• Storage temperature: -40 to 185ÅãF (-40 to 85ÅãC)
• Relative humidity: 0 to 90%, non-condensing
Agency Approvals
• UL(R)/EN 61010 Listed, File E185611 QUYX
• UL(R) 508 Reviewed
• CSA CC.C#14, File 158031
• FM Class 3545 (configurations with limit modules)
• AMS 2750 E compliant: Analog input process values. Tip: Maximize
field calibration accuracy and uniformity by using advanced F4T
features such as Calibration Offset and Linearization Function
Blocks. Refer to user manual for details.
• RoHS by design, China RoHS Level 2, W.E.E.E.
• CE
• Windows(R) Hardware Certification
User Interface
• 4.3 inch TFT PCAP color graphic touch screen
• LED backlife >50K hours
• 4 keys: Home, Main Menu, Back, Help
• Multiple languages
• English, German, French, Italian, Spanish, Japanese, Korean
and Chinese
• USB wired or wireless mouse functionality
• Right click for 4 keys: Home, Main Menu, Back, Help
Control Loops
• 1 to 4 PID or ON-OFF control loops
• 0 to 6 Limit loops
• User-selectable action: heat, cool or heat/cool
• Auto-tune with TRU-TUNE+ adaptive control
Control Loops and Over-temperature Limits
• Input sampling: 10Hz
• Output update: 10Hz
• Ethernet Modbus(R) TCP
• Isolated communications
Profile Ramp and Soak Option
• Profile engine affects 1 to 4 loops in sync
• 40 profiles with 50 steps per profile
Data Logging
• User selectable parameters: Up to a maximum of 128 active
parameters depending on configuration
• Logging interval: Programmable increments between 0.1 seconds
and 60 minutes if logging to internal memory. Logging directly to
USB; 1.0 seconds to 60 minutes
• File types: .CSV for standard data logging or proprietary format for
encrypted data log option
• Storage: 80MB internal memory or to USB memory stick
• File transfer: Internal memory to USB host port or to Ethernet
Modbus(R) TCP
• Transfer options: On demand by user or user programmable based
on when a new data log file record is available. Utilizes TFTP and
Samba protocols
• Record: Date and time stamped

For a Watlow Quote on the F4T or other Watlow Products, click HERE!


Watlow Process Controller F4T with Ramp Soak, Batches, 1-4 loops and communications.

Tuesday, May 21, 2019

Bosch Green Therm Heaters

Bosch Thermotechnology GreenTherm Tankless Water Heaters


An ideal solution for energy efficient hot water

Greentherm and Therm gas tankless water heaters include high efficiency gas condensing and non-condensing tankless water heaters with more compact models and greater installation versatility to satisfy every residential and commercial application.

The Greentherm 9000 offers an efficiency rating of UEF up to 0.96 and innovative features for easy installation, operation and simple maintenance. You will enjoy an industry-leading 15-year warranty on the heat exchanger and a full 5-year limited warranty on parts.

Replacing a tank?

The Greentherm 9000 series indoor models were specifically designed with top connection for water, integrated drain ports so isolation valves are not needed, and a unique integrated sensor technology that auto-calibrates, making the switch to tankless water heating quick and easy.

Choose from seven models to ensure a configuration for any need from small home or condo to large commercial applications. Each model includes a conversion kit from natural gas (NG) to liquid propane(LPG), and flexible venting options to keep installation simple.
* Named CES 2017 Innovation Award Honoree. The prestigious CES Innovation Awards are sponsored by the Consumer Technology Association™. CES Innovation Awards celebrate outstanding product design and engineering in brand-new consumer technology products

The Greentherm 9000 removes the barriers to upgrading to an energy efficient tankless water heater with innovative top connections for water, unsurpassed efficiency and cutting-edge technology for reliability and long-life.

Beautiful, hardworking

All Greentherm 9000 Series models feature sleek, rounded corners on the metal cabinet, making these water heaters as beautiful as they are energy-efficient. The premium Greentherm 9900i SE model has a unique, stylish glass front and integrated Wi-Fi control (available as options on other models) enabling the homeowner to control the water heater remotely with the free mobile app.

Features and Benefits

  • Top mounted water connections lowers labor & parts requirements
  • Easy conversion from existing tank water heater
  • High-resolution, built-in touch screen for intuitive appliance control
  • Built-in recirculation pump that minimizes water waste waiting for hot water at the faucet
  • Automatic OptiFlow combustion management system minimizes installation setup time and maximizes product performance
  • Dedicated indoor and outdoor mounted units available – no outdoor vent kit required
  • Built-in freeze protection on all models, ideal for colder climates

Bosch Greentherm T9800 SE 199, 199,000 BTUs Tankless Water Heater, 9000 Series, 99% EF, LP or NG

Bosch Greentherm T9900 SE 160, 160,000 BTU Tankless Water Heater, 9000 Series, 99% EF, NG or LP, with Recirculating Pump

Bosch Greentherm T9800 SE 160, 160,000 BTUs Tankless Water Heater, 9000 Series, 99% EF, Ng or LP

Bosch Greentherm T9900 SE 199, 199,000 BTU Tankless Water Heater, 9000 Series, 99% EF, NG or LP, with Recirculating Pump

Bosch Greentherm T9900i SE 199, 199,000 BTU Tankless Heater, 9000 Series, 99% EF, NG or LP, with Recirculating Pump

In stock and ready to go.


Anderson-Bolds sells Bosch Green Therm Gas Tankless Water Heaters and Tronic Electric Tankless Heaters

Monday, April 29, 2019

ATC Diversified Multifunction Meter VCFP96M

Anderson-Bolds sells the Diversified Electronics Electric Meter for Industry

Diversified Electronics Industrial Controls - Go Orange

To get a quote use our ATC/Diversified Parts Form HERE!

Diversified Electronics, Orange Controls for automation.

The VCFP96M is a complete single phase and three phase digital metering system suitable for low, medium and high voltage control panels, gensets, load banks, building management systems and power management systems. The VCFP96M can be used on single phase, three phase three wire as well as three phase four wire balanced or unbalanced systems. The six easy to access front control keys are used for scrolling up or down through the parameters being measured and displayed such as voltage, current, power factor, power (active, reactive, apparent), energy and frequency. Output specifications include pulse output and RS485 Modbus RTU communication protocol compatible with PC, PLC, RTU, data loggers and SCADA programs. The VCFP96M is available in a 96 x 96 mm panel mount housing (front panel IP65) with red led display for easy viewing in a variety of conditions.



ATC Diversified VCFP96M UL Listed Meter

Input Specifications

Electrical Connection
3Ø - 3 wire, 3Ø - 4 wire, 2Ø - 3 wire, 1Ø - 2 wire
Input Voltage Range
11 to 300V AC, (Phase to Neutral) 19 to 519V AC (Phase to Phase)
Input Current Range
Nominal 5A AC (Min-11mA, Max-6A)
45 to 65Hz
Display Scrolling 
Automatic / Manual (Programmable) 
Power Consumption
8VA Max
Display Reset 
Programmable (For energy)
For energy :0.01k, 0.1k, 1k, 0.01m, 0.1m, 1m (depending upon CT ratio x PT ratio)For Power, Voltage, Current : Auto resolutionFor Power factor : 0.001
Voltage (L-N / L-L) : ±0.5% of F.S. Power Factor ±0.01 Current ±0.5% F.S.Frequency : ±0.1% For L-N Voltage >20VFor L-L Voltage >35VPower (Active, Reactive, Apparent) : 1%Energy (Active, Reactive, Apparent) : Class 1
Memory Retention
10 years (For energy) 
Measuring Parameters

Voltage (L-L / L-N) (Individual / Average), Current (I1, I2, I3) (Individual / Average),Frequency, Power Factor (Individual /Total), Active, Reactive & Apparent power (Individual / Total),Active, Reactive & Apparent Energy (Total), Demand (Min / Max Active Power, Min/Max Reactive Power, Max Apparent Power), %THD up to 31st Level Max Demand Current, Neutral Current, Phase Sequence Detection

Output Specifications

Pulse Output
Voltage Range : External 24V DC maxCurrent Capacity : 100mA maxPulse Width : 100 ms ± 5 ms
CommunicationInterface and Protocol
Communication Address
1 to 255
Transmission Mode
Half duplex
Transmission Distance
500 meter maximum
Transmission Speed
300, 600, 1200, 2400, 4800, 9600, 19200 (in bps)
None, Odd, Even 
Stop Bits
1 or 2
Response Time
100 ms (max and independent of baud rate)

• 3Ø True RMS (Voltage, Current)
• 3Ø Power (Active, Reactive, Apparent), Energy (Active, Reactive, Apparent)
• Programmable CT/PT Primary/Secondary
• CT Polarity Error Detection
• Variable Pulse width Selection
• Single Phase Network with Phase Selection
• Modbus RTU Communication (RS485)
• Neutral Current Measurement
• THD Up to 31st Level.
• Single Pulse Output / Demand Phase Sequence Detection


ESD Immunity
IEC 61000-4-2
 Level IV (Air discharge : 15kV),(Contact Discharge : -8kV
Surge Immunity
IEC 61000-4-5
+/- 2kV common mode, (Line to ground)+/- 1kV differential mode, (Line to Line)
Radiated Susceptibility
IEC 61000-4-3
Level III, 80 to 1000MHz (10V/m)Level II, 1.4GHz to 2GHz (3V/m)Level I, 2GHz to 2.7GHz (1V/m)
Conducted Susceptibility
IEC 61000-4-6
Level II (3V/m)
Voltage Dips and Interruptions
IEC 61000-4-11
Dips : 0% residual voltage / 1 cycle (Criteria B), 40% residual voltage / 10 cycles 50Hz / 12 cycles 60Hz (Criteria C)70% residual voltage / 25 cycles50Hz / 30 cycles 60Hz (Criteria C)Interruptions : 0% residual voltage /250 cycles 50Hz / 300 cycles 60Hz(Criteria C)
Conducted Emission
Radiated Emission
Electrical Fast Transient
IEC 61000-4-4
Level III (2kV)


ATC / Diversified is a manufacturer of Industrial Automation Controls including Timers, Counters, Voltage Monitors, Current Monitors, Voltage Power Alerts, Time Delay Relays, Temperature Controls, Duplexors, Alternating Relays and Motor Protection.