Littelfuse Off Delay Adjustable Timer TDBL12D

Anderson-Bolds has in stock the Littelfuse Adjustable TDR working on 12vdc.  The TDBL12D can be shipped within 24 hours of an order.

LittelFuse SSAC TDR TDBL12D, with a .1-102.3 Second Adjustable Range. 10 amp rating and 12 volts DC (Octal Socket required). The Timer is an Delay-On-Break (Off Delay) time delay relay. The Time Delay Relay is now made by Little Fuse. UL, CSA and CE. Previous manufacturers were SSAC, Entrelac, ABB and Sycom. Littelfuse part number is TDBL12D

Buy the Timer/TDR HERE!

TBDL12D 

Anderson-Bolds
216-360-9800
www.anderson-bolds.com

SSAC/Littelfuse Voltage Monitor HLMUDLAAA

Voltage Monitor Protection Relay HLMUDLAAA from Anderson-Bolds
Made by Littelfuse

Contact Anderson-Bolds

LittelFuse SSAC Voltage Monitor HLMUDLAAA is a universal voltage monitor. 10 amp output relay rating. The HLM Voltage Monitor senses over or under voltage AND phase unbalance and frequency fluctuations and trips if any go oout of range. The Voltage Monitors are currently made by Little Fuse. UL, CSA and CE. Previous manufacturers were SSAC, Entrelac, ABB and Sycom.

BUY the HLMUDLAAA

The HLMU Series is a universal voltage, encapsulated, 3-phase voltage monitor. It continuously measures the voltage of each of the three phases with microcontroller accuracy and compares the value to preset trip points. It separately senses phase reversal and loss; over, under and unbalanced voltages; and
over or under frequency. Protection is assured during periods of large average voltage fluctuations, or when regenerated voltages are present. The unit trips within 200ms when phase loss is detected. Adjustable time delays are included to prevent nuisance tripping and short cycling of sensitive equipment. The isolated, 10A, DPDT relay contacts trip when a phase voltage exceeds the trip limits for the trip delay. Nominal line voltage, voltage unbalance, and time delays are knob adjustable. The phase loss setpoint and the acceptable frequency range are fixed. Both delta and wye systems can be monitored; no connection to neutral is required.

Voltage Monitor HLMUDLAAA

BENEFITS

Constant monitoring to protect against phase loss, phase reversal; over, under, and unbalanced voltage; over and under frequency
Flexibility to work in 200 to 480VAC applications
Installation flexibility
Provides diagnostics of relay, fault and time delay status
Protects against shock, vibration, and humidity Meets IEC 61000 safety requirements

Operation

Upon application of line voltage, the output is de-energized
and the restart delay begins. If all the three-phase voltages are within the acceptable range, the output energizes at the end

of the restart delay. The microcontroller circuitry automatically senses the voltage range, and selects the correct operating frequency (50 or 60Hz). The over and under voltage trip points are set at ± 10% of the adjusted line voltage. When the measured value of any phase voltage exceeds the acceptable range limits (lower or upper) the trip delay begins. At the end of the trip delay the output relay de-energizes. If the phase voltage returns to an acceptable value before the trip delay expires, the trip delay is reset and the output remains energized. Under, over, and unbalanced voltages plus over or under frequency must be sensed for the complete trip delay before the unit trips. The unit trips in 200ms when phase loss or reversal are sensed. The unit will not energize if a fault is sensed as the line voltage is applied. 

Reset: Reset is automatic upon correction of the voltage or frequency fault or phase sequence.

Restart Delay Options
L = Lockout or minimum OFF time. The restart delay begins when the output trips. The unit cannot be re-energized until the restart delay is complete. This provides a minimum off time

or lockout time to allow equipment sensitive to short cycling, time to reset. If the fault is corrected after the restart delay is complete, the output energizes immediately. The restart delay also occurs when line voltage is applied/reapplied.

R = Restart Delay on fault correction. The restart delay begins when line voltage is reapplied or when a voltage fault is corrected. This option is normally selected when staggered restarting of multiple motors on a power system is required.
N = No Restart Delay. 0.6 second initialization delay on application of line voltage applies.
Restart Notes: All restart options remain reset when the following conditions are detected:
1. Phase loss (phase unbalance greater than 25%) 2. Average line voltage less than 120VAC
3. Phase reversal

The restart delay begins when the condition is corrected.

LED Operation
The LED flashes green during the restart delay, then glows green when the output energizes. It flashes red during the trip delay then glows red when the output de-energizes. It flashes red/green if phase reversal is sensed. If a fault is sensed during the restart delay, the LED will glow red during that portion or the full restart delay. 

Type

3-phase delta or wye with no connection to neutral

Range
240 380 480

Voltage Adj. Range
200-240VAC 340-420VAC 400-480VAC

Frequency

50 or 60Hz 50Hz 60Hz

Line Voltage Max.
550VAC
AC Line Frequency
50/60 Hz automatically detected
Phase Loss
≥ 25% unbalance
Response Time

≤200ms 

Overvoltage Trip Voltage 
109 - 113% of the adjusted line voltage
 Reset Voltage

-3% of the trip voltage

Undervoltage Trip Voltage
88 - 92% of the adjusted line voltage
Reset Voltage
+3% of the trip voltage 

Voltage Unbalance Trip Setpoint
Adjustable 2 - 10% or specify fixed unbalance of 2 - 10% in 1% increments
Reset on Balance
≅ -0.7% unbalance

Trip Delay Active On

Over/under voltage, voltage unbalance, over/under frequency

Range
Adjustable from 1 - 30s or specify fixed delay 1 - 30s in 1s increments
Tolerance
±15%
Restart Delay Range
Adjustable from 0.6 - 300s; if no restart delay is selected a 0.6s initialization delay applies 

Tolerance

±15%
Over/Under Frequency
±4%; Reset ±3%; 50/60 Hz
Phase Sequence
A, B, C, L1, L2, L3

Response Time-Phase

Reversal & Phase Loss
≤200 ms
Reset
Automatic

Output 

Isolated Electromechanical Relay

DPDT

10A resistive @ 240VAC;
8A resistive @ 277VAC; NO-1/4 hp @ 120VAC; 1/3 hp @ 240VAC
Protection
Phase Reversal/Failure

ASME A17.1 Rule 210.6
Motors and Generators
NEMA MG1 14:30, 14:35
Surge
IEEE C62.41-1991 Level B
Isolation Voltage
≥ 2500V RMS input to output
Circuitry
Encapsulated

Dimensions

H 76.7 mm (3.0”); W 50.8 mm (2.0”);

D 41.7 mm (1.64”)

Termination
Screw terminal connection up to 12 AWG (3.3 mm2) wire
  

 Temperature

 -40° to 60°C / -40° to 85°C

BUY the HLMUDLAAA

www.anderson-bolds.com

Anderson-Bolds
216-360-9800

SSAC Products

Timer-DOM 100-240VAC/DC 1A DIPsw 1-1023s 2x2

The TDU and KSDU Series are encapsulated solid- state, delay-on-make timers that combine digital timing circuitry with universal voltage operation. The TDU offers DIP switch adjustment allowing accurate selection of the time delay over the full time delay range. The KSDU is factory fixed from 0.1s to 10,230s and does not include the DIP switch. These series are excellent choices for process control systems and OEM equipment

3Ph Voltage Monitor 200-480VAC Adj 8 pin

The PLMU Series continuously measures the voltage of each of the three phases to provide protection for 3-phase motors and sensitive loads. Its microcontroller senses under and overvoltage, voltage unbalance, phase loss, and phase reversal. Protection is provided even when regenerated voltages are present. Universal voltage operation and standard base connection allows the PLMU to replace hundreds of competitive part numbers.

Liquid Level-Drain Dual 120VAC Relay Adj 8Pin

The LLC5 provides dual probe conductive liquid level control in a convenient octal plug-in package. Models are available for fixed fill or drain operation. Isolated, pulsed DC voltage on the probes prevents electrolytic plating. Less than 1 mA of current is used to sense the presence of conductive liquid between the probes and common. On adjustable units, the sensitivity adjustment eliminates false tripping caused by floating debris and foaming agents.

Flasher 120VAC 1A 75 fpm 6 inch wires

The FS100 Series (low amp) may be used to control inductive, incandescent or resistive loads. This series offers a 1A (fullwave) or a 2A (halfwave) steady state, 10A inrush solid-state output and may be ordered with an input voltage of 24 or 120VAC. The FS100 Series offers a factory fixed flash rate of 75 FPM or may be ordered with a fixed, custom flash rate ranging from 45 to 150 FPM.